Motorcraft 2150 2-Barrel Carburetor (Ford 1975–1985): Interactive 3D Exploded View

Interactive 3D exploded view of the Motorcraft 2150 two-barrel carburetor: 19 named parts, an explode slider and a downloadable GLB model.

Motorcraft 2150 2-barrel carburetor – 3D model in the photo view angle

The Motorcraft 2150 is a Ford two-barrel (2V) carburetor, an evolution of the earlier Autolite 2100. It was fitted to many Ford V8s of the 1970s, notably the 351M and 400 engines in Ford cars and light trucks such as the Bronco. This page lets you take one apart on screen: drag to rotate, scroll to zoom, and click any part to identify it.

Open the 3D viewer full screen · open at the photo angle

How to use the viewer

  • Rotate and zoom: drag to rotate, use the mouse wheel (or pinch) to zoom, and click a part to identify it.
  • Explode slider: the slider at the bottom of the viewer (labeled “Explosión”) pulls the carburetor apart or pushes it back together.
  • Buttons: “Armar” (Assemble) and “Desarmar” (Disassemble) animate the whole carburetor; “Etiquetas” (Labels) shows or hides the part numbers; “Rotación” (Rotation) turns auto-rotation on or off; “Reiniciar vista” (Reset view) restores the default camera.
  • Parts list: the panel on the right names all 19 parts in English. Click a name to highlight the part.
Motorcraft 2150 2-barrel carburetor – 3D model in the photo view angle
The 3D model shown at the same angle as a typical reference photo (?view=photo).

Identification

Ford identifies each calibration with a code printed on a tag on the carburetor, for example D7TE-APA. The first characters give the decade and model-year digit (D7 = 1977); the rest point to the engine and vehicle application and the design revision. Versions of the 2150 differ internally, so always match the full tag number when you order a rebuild kit or a replacement carburetor. The close-up below shows the tag area on the 3D model.

Close-up of the Motorcraft 2150 3D model showing the air horn, tag and screws
Close-up of the air horn on the 3D model, including the identification tag.

Typical applications

The 2150 was used on Ford and Mercury cars and on Ford light trucks (F-Series, Bronco, Econoline) with V8 engines such as the 302, 351M/351W and 400, mostly in the late 1970s and early 1980s. Which carburetor a vehicle actually used depends on the model year, engine, transmission and emissions calibration, so check the tag on your own unit and a Ford service manual rather than relying on a general list.

The exploded view

Move the explode slider all the way up and the model separates into 19 numbered parts:

  1. Choke Plate & Shaft
  2. Air Horn Assembly
  3. Air Horn Gasket
  4. Fuel Inlet Needle & Seat
  5. Float Assembly
  6. Booster Venturi Cluster
  7. Main Jets (2)
  8. Accelerator Pump Cover & Diaphragm
  9. Accelerator Pump Rod
  10. Power (Enrichment) Valve
  11. Main Body & Fuel Bowl
  12. Idle Mixture Screws (2)
  13. Electric Choke Cap
  14. Choke Housing
  15. Choke Pull-down Diaphragm
  16. Fast Idle Cam
  17. Throttle Plates & Shaft
  18. Throttle Body
  19. Mounting Gasket
Motorcraft 2150 carburetor 3D exploded view with 19 numbered parts
Exploded view with part numbers. The numbers match the parts list in the viewer.

Real carburetor vs. the 3D model

Real Motorcraft 2150 photo next to the 3D model at the same angle
A real Motorcraft 2150 (left) next to the 3D model (right).

The model is an illustration built for study and identification. It is not a factory drawing, so check dimensions and part details against the real carburetor or the Ford service manual.

Download

Want to open the model in your own 3D software? Download the GLB model (about 18 MB, 19 named parts, real-world scale).